Infrared Remote Control Systems

NASA ISS On-Orbit Status 1 July 2011

As part of the crew's regular morning inspection tour, CDR Borisenko performed the routine checkup of circuit breakers & fuses in the DC1 (Docking Compartment). [The monthly checkup in DC1, MRM1 & MRM2 looks at AZS circuit breakers on the BVP Amp Switch Panel (they should all be On) and the LEDs (light-emitting diodes) of 14 fuses in fuse panels BPP-30 & BPP-36. MRM2 & MRM1 were derived from the DC1 concept and are very similar to it.] With its battery recharged overnight, FE-1 Samokutyayev set up the Russian DZZ-12 RUSALKA ("Mermaid") hardware at SM window #9 for another sun-glint observation session, using the hand-held spectrometer (without use of the TIUS three-stage rate sensor), synchronized with the coaxially mounted NIKON D2X camera for taking snapshots, and later downloaded the data to laptop RS1 for subsequent downlink via OCA. The equipment was then torn down and stowed away. [RUSALKA is a micro spectrometer for collecting detailed information on observed spectral radiance in the near IR (Infrared) waveband for measurement of greenhouse gas concentrations in the Earth atmosphere], In the Lab, FE-3 Ron Garan had several hours of work, removing & replacing the failed Lab MCA (Major Constituent Analyzer) Mass Spectrometer (ORU 2), to be returned on ULF7. The R&R was not fully completed due to a time-consuming issue with fasteners. [For the R&R, Ron first had to remove the Lab MCA Drawer for which the D6 rack had to be rotated down (away from the wall). To gain access to the MSA (Mass Spectrometer Assembly), the VGA (Verification Gas Assembly) also had to be taken out temporarily. The failed spectrometer has been removed and prepacked for return. Activities will be replanned to complete this R&R and activate the MCA.] Meanwhile, Andrey Borisenko & Sergei Volkov spent several hours in the SM (Service Module) on the long-awaited major TVIS treadmill IFM (Inflight Maintenance). The gyroscope removal went well, and no crew calldowns were required. [After taking the TVIS out of the "pit" in the SM floor, Andrey & Sergei removed the failed treadmill gyroscope, to be returned on Atlantis. While TVIS was out of the pit, they lubricated the transfer case, vacuumed the screens, checked the Aft Right Stabilizer Witness Mark and inspected one corner. TVIS was then temporarily stowed to await the new gyro, to be delivered on ULF7. The activities were monitored by MCC-Houston TVIS specialists.

Remote Repeater | Sewell Infrared (IR) Remote Control Repeater Kit ...

Great Deals on Sewell Infrared (IR) Remote Control Repeater Kit (Black) at low price.Order Now get great product and cheap price.You can save $30.00.Purchase at online store fast delivery Click Here.

Sewell Infrared (IR) Remote Control Repeater Kit (Black) Informations :

Does your entertainment system have wooden doors, or would you like to mount your components in a closet? Without a clear line of sight infrared (IR) signals from a remote control will not reach the equipment. We have the answer. Our remote control repeater kit contains all equipment necessary to remotely operate 4 components (expandable to 12 components) using your standard remotes. Mount the IR receiver in a central location and connect to the IR distribution block. This block repeats the signals through emitters to your electronic components. Your components may now be mounted in your entertainment center, closet or another room! The kit is self-contained and easy to connect. With this kit, you may mount a receiver in a convenient place on or near your entertainment system. The receiver has a 9 foot cable that is then attached to the repeater system that is mounted in your entertainment cabinet. The kit includes 4 emitters. These emitters are connected from the repeater system and placed over the IR receiver of the equipment. The IR receiver and IR repeater have blinking blue LEDs to confirm receipt of the IR signal; the IR repeater is designed for mounting on shelf or wall. You can use your existing remotes for simple installation and hookups.

Sewell Infrared (IR) Remote Control Repeater Kit (Black) Feature :

Forward infrared signals to operate electronic components behind closed doors IR Receiver has size of 2.25in (L) x 0.5in (W) x 0.5in (H); 9ft cable is attached for connection to IR Repeater Emitters have a dual emitter y-cable; overall length is 9 feet; final 3 feet may be separated Simple to use; Controls 4 devices (expandable to a maximum of 12) Kit includes: IR Distribution Block; Mini IR Receiver; (2) Dual IR Emitters; AC/DC Adapter

Compare Price Sewell Infrared (IR) Remote Control Repeater Kit (Black)

Special Offers

Available from 1 Store.

Mims Circuit Scrapbook

A Single-Channel Infrared Remote Control System Near infrared radiation is well suited for use as a carrier of trigger signals in miniature remote control ...

New York

Silhouette* Shades with the new PowerRise® remote control system raises or lowers your shades to any height with just the push of ...

Infrared Remote Control for Stereo System

Robot Building for Beginners

Object Detection and Infrared Remote Control A popular technique for detecting the presence of an object is to use an infrared LED to blink a signal and ...

Proceedings of the Second International Conference on Active Media Technology, Chongqing, PR China, 29-31 May 2003

Universal infrared remote control: The system allows the user to control any device that has ordinary IR remote controls. We prepare a microserver with an ...